Zum Inhalt springen

HaWiWe

Holzdesign und 3D-Druck

Projekte
Meine CNC
Meine Maschinen
Shop

Suchen nach:

HaWiWe

Holzdesign und 3D-Druck

Projekte
Meine CNC
Meine Maschinen
Shop

Autorenname: Philipp

Hello world!

Philipp / 27. Oktober 2024

Der Webspace ist bestellt, die ersten Seiten gestaltet. Nun ist es Zeit, die Seite öffentlich zu machen. Es wird hier […]

← Zurück 1 2

Aktuelle Videos

When they were 7 and 9 I taught my girls to play Catan. They loved it a lot which hardened my resolve to finally tackle this project (the wood had been sitting in my shop, already planed for at least a year). The design is based on Garrett's Catan set in the V1 Engineering Forum with minor changes (for instance the symbols, which in this version were drawn by my daughter - the sheep are soooo cute!).

00:00 - Xbox Controller and zeroing.
00:53 - Cutting the tiles.
01:04 - Pear - Clay.
01:40 - Bog Oak - Ore.
02:11 - Satinwood - Wheat.
02:39 - Maple - Sheep.
02:58 - Wenge - Wood.
03:11 - Honey Locust - Desert.
04:01 - Planing Cherry for the sea.
04:33 - Cutting the border.
06:25 - Sanding the harbours.
07:10 - Engraving the numbers.
08:30 - Printing the figures.
09:09 - Engraving the ressources.
11:15 - Bath in oil.
11:32 - Removing surplus oil.
13:15 - Custom box.
14:18 - Box done - nearly.
14:36 - Engraving the lid.
15:03 - Putting the box together.
19:47 - The finished board. Game with my daughters.

I had some problems with my X axis losing steps, because I am sometimes really pushing the LR hard with a dull endmill (stupid me). So I wanted to try a closed loop stepper and guys: it's awesome.

It took me half an hour to install, one hour including crimping etc. Regrettably Y/Z can't have closed loop steppers, because they are too big to fit the side plates.

The "clicking" you can hear when pushing it is my collet that isn't tight... Also, I can't go faster than 24000mm/min with 6400 Microsteps, because the controller does not support more calculations. If I halved the microsteps, I might be able to run it at double the speed... :P

For V1 Engineering's 10th birthday I made a commemorative box to celebrate Ryan's achievement. Without V1, my hole woodworking "career" might have been completely different (though I doubt it would have happened at all), so I felt it fitting to put some time and effort into it. :)
If you like my videos and the stuff I make, I'd feel honoured if you checked out www.hawiwe.de, where you can find plans for most of the things that I do here for free.

00:00 - Preparing the wood.
00:55 - Resawing.
01:18 - Cutting the inlay plug.
02:50 - Cutting the bottom.
04:23 - Cutting the top.
04:34 - Toolchange in EstlCAM.
05:32 - Inlay on top.
07:37 - Test fit.
08:07 - Masking and gluing.
10:00 - The new(ish) press.
10:45 - DIY Drum Sander in action.
11:06 - All kinds of other sanding.
11:29 - Oil.
12:03 - Magnets.
12:45 - All done.

Mehr laden…. Abonnieren

Warenkorb

Kontakt

Shop

AGB
Widerrufsrecht
Versand und Zahlung

Informationen

Impressum
Datenschutzerklärung

Copyright © 2025 HaWiWe

✕

Nach oben scrollen